Your Trusted Source for Industrial Electrical Components
Industry Applications

LEM Current Sensors in Solar Inverters: Measurement Applications and Key Requirements

A practical look at DC and AC current measurement in solar inverters, sensor bandwidth, isolation, EMC and leakage-current differences.

SafeCirk Editorial  ·  Mar 27, 2025  ·  LEM  ·  4 min read

A solar inverter converts electricity from photovoltaic modules into power that a load or electrical grid can use. To control that process, its electronics need trustworthy measurements of current at selected points in the power path. Different measurements serve different purposes, and a sensor that is ideal for a control loop is not necessarily appropriate for protective leakage-current monitoring.

LEM publishes application information for renewable-energy systems and identifies specific current-sensor families for solar inverters. The most useful engineering approach is to begin with the measurement task rather than with a part number.

Where current is measured in a PV inverter

PV-side or DC-side measurement can inform input regulation, power tracking, diagnostics and supervision. The waveform can include DC current with ripple and switching-related transients. The measurement range must cover expected generation levels as well as operational excursions.

AC-side measurement supports current control and grid-interface supervision. Depending on topology, sensors may be placed on inverter phases or at other defined nodes. Engineers should distinguish fundamental-frequency accuracy from dynamic response under switching interference.

Residual or leakage-current measurement is a separate task. In transformerless PV inverters, monitoring unintended current paths to earth can support protective functions. That application typically has different sensitivity, fault-detection and approval requirements from measuring a large operational phase current.

Why isolation and interference matter

An inverter combines high DC bus voltage with fast-switching semiconductor devices. Large dv/dt and common-mode noise can stress the measurement chain. The engineer must verify a transducer's isolation ratings, immunity, response and installation layout, alongside the electronics receiving its signal. Mechanical separation alone is not sufficient evidence of compliant isolation.

The output must also match the controller: supply voltage, analog or digital format, reference, filtering and bandwidth all affect integration. It is important to check sensor performance at temperature extremes and during power-up or transient conditions.

LEM product families as application examples

LEM describes the LZSR family as a current-sensor solution especially adapted to certain solar-inverter power ranges. The company's published LZSR information discusses closed-loop measurement, DC/AC/pulsed current, isolation and low offset drift. These are reasons to investigate the family, not evidence that every LZSR variant fits any PV inverter.

LEM also presents the LDSR family for earth-leakage current measurement in transformerless single-phase PV inverters. LDSR has a different measurement purpose from a main phase- or DC-current sensor. It should not be compared or substituted solely by checking a current-rating number. Other LEM families appear in the manufacturer's renewable-energy application overview and should be considered against the exact architecture.

A practical sensor selection workflow

  1. Draw the inverter topology and label the exact measurement position.
  2. Define the useful current waveform: DC component, AC frequency, ripple and potential transients.
  3. Specify nominal, peak and minimum meaningful current.
  4. Document feedback bandwidth, latency and acceptable error across temperature.
  5. Establish insulation, EMC and installation requirements for that location.
  6. Check supply, signal interface, footprint and primary-conductor routing.
  7. If the measurement supports a protective function, validate the full safety concept and required certification path separately.

This sequence prevents the common mistake of selecting a “solar sensor” without first defining whether the task is power control, monitoring or leakage detection.

Frequent design and purchasing pitfalls

A sensor rated for AC and DC current does not necessarily provide the resolution required for a low leakage threshold. Conversely, a sensitive leakage sensor is not intended to carry the same measurement burden as a high-current control sensor. Another mistake is neglecting temperature drift and switching noise while relying on catalog accuracy at room temperature.

Avoid assuming an application-page reference replaces a datasheet. The selected suffix, conductor arrangement and mounting details can change the engineering assessment.

Useful information for a quotation

A good RFQ identifies inverter topology, DC-bus and operating-voltage environment, measurement location, expected AC/DC current and ripple, peak events, required measurement bandwidth, insulation and signal interface. State whether the application is phase feedback, DC monitoring or residual-current detection. Include the complete LEM model code or an engineering drawing when available.

Conclusion

Solar inverters need more than one kind of current information. Good sensor selection begins with the circuit node, waveform and measurement purpose; then it checks insulation, interference, accuracy and mechanical fit. LEM's solar-related families provide starting points for a qualified shortlist, but final approval requires the original datasheet and system-level testing.

Manufacturer references