Your Trusted Source for Industrial Electrical Components
Industry Applications

Current Measurement in Battery Energy Storage Systems

An engineer-focused overview of where current is measured in energy storage equipment, what sensor specifications matter, and how to evaluate suitable measurement technologies.

SafeCirk Editorial  ·  Dec 17, 2025  ·  LEM  ·  5 min read
Preview draft — technical review required before publication. This guide is not a substitute for the system safety design, component datasheets, or engineering approval. No specific product is represented as pre-approved for a particular BESS design.
Representative LEM current sensor product imagery supplied by SafeCirk
Representative LEM product photograph supplied by SafeCirk. Product suitability must be verified separately for each energy storage application.

Battery energy storage systems (BESS) exchange power between battery packs, power-conversion equipment, and external loads or the grid. Reliable current measurements are one of the inputs used for monitoring energy flow, estimating operating state, controlling converters, and detecting abnormal conditions. However, a sensor that is suitable for a battery DC connection may not meet the needs of an AC converter output or a fast protection function.

This article outlines a practical review process for engineers and technical buyers. It focuses on application requirements rather than recommending one sensor model for every installation. LEM's published application guide includes battery energy storage systems and power-conversion applications as distinct contexts, reflecting the importance of selecting technology around the actual measurement location.[1]

1. Identify where current needs to be measured

Begin with the system block diagram. The measurement point determines whether the device must measure DC, AC, both polarities, fast transients, or a combination of these. Examples include:

Measurement pointTypical purposeQuestions to resolve
Battery pack DC connectionCharge/discharge current monitoring and information for system managementIs bidirectional DC measurement required? What continuous and transient currents occur?
DC link in power conversion equipmentConverter control, energy-flow supervision and diagnostic measurementsWhat are the switching environment, insulation requirements and response-time needs?
Converter AC outputAC current feedback, grid-interface monitoring and controlWhat frequency components, bandwidth and phase accuracy are required?
Auxiliary or leakage-related circuitsDedicated monitoring or protective functionsIs a specialized residual-current or other protection device required rather than a general current transducer?

The table is a conceptual overview, not a complete BESS protection architecture. The engineering team must define the measurement points and protective functions for its own design.

2. Check bidirectional measurement and current range

Charging and discharging can reverse the current direction through a battery connection. If the measurement system must distinguish both conditions, confirm that the sensor and its interface support the required bipolar measurement and suitable zero-current reference.

Review continuous current, anticipated overloads and transient peaks separately. The maximum peak rating, usable measurement range and permissible duration may differ. Do not select a sensor based only on the nominal battery current or the largest number in a marketing summary.

3. Evaluate accuracy across real operating conditions

For energy management or battery-state estimation, measurement error at low current may be important even when the installation also experiences high peak currents. Review the manufacturer's specifications for accuracy, offset, temperature drift, linearity and the conditions under which each value is stated.

System accuracy also depends on signal conditioning, ADC resolution, calibration, installation and the control algorithm. A sensor's headline accuracy does not automatically describe the accuracy of the complete monitoring system. TI's battery-current measurement guidance discusses tradeoffs between shunt and magnetic technologies, including accuracy and temperature-related considerations.[2]

4. Separate monitoring requirements from fast protection requirements

A current value used for energy accounting or supervisory monitoring may not require the same bandwidth and latency as a fast converter-control or overcurrent-protection function. Determine the necessary response time and frequency content for each purpose before comparing sensors.

Important: Do not assume a general-purpose measurement channel can replace dedicated protective hardware. Protection architecture, thresholds, fault response and functional-safety requirements must be validated by the responsible engineering team.

5. Compare measurement technologies

Two broad approaches are common in current measurement, though product implementations vary considerably:

ApproachPotential strengthsPoints to verify
Resistive shunt with appropriate electronicsDirect electrical measurement; potentially good linearity and DC measurement performancePower loss and heating, common-mode voltage, galvanic isolation needs, layout and amplifier limits
Magnetic sensing (for example, Hall-effect based)Can measure AC and DC without routing the full measured current through a precision sense resistor; isolated implementations are availableOffset, temperature behavior, noise, bandwidth, conductor position, magnetic interference and installation

The right choice depends on the electrical architecture and verified device performance. For example, TI's high-side shunt-based reference design illustrates a defined, low-voltage bidirectional battery-monitoring implementation; its ratings must not be extrapolated to high-voltage BESS installations.[3]

6. Review electrical isolation and installation requirements

Energy storage equipment may contain hazardous voltage levels. Confirm the required insulation coordination, working voltage, transient withstand, clearances and other applicable electrical-safety requirements with qualified engineers and the relevant standards. Where isolation is necessary, verify the actual product's published isolation specifications—not merely that it is described as a “current sensor.”

Also examine conductor or busbar dimensions, aperture, mounting orientation, thermal surroundings, vibration and cable routing. Mechanical fit and electromagnetic environment can influence whether a technically promising device can be installed correctly.

7. Match the sensor output to the control system

Check the output type (analog voltage, current or digital), supply-voltage range, reference conditions, signal scaling, output impedance where applicable, and expected behavior at startup or during an out-of-range condition. The data acquisition and control electronics must be compatible with these characteristics.

If the sensor is used in control loops, account for measurement delay and signal filtering within the complete system. A datasheet may specify a sensor characteristic, but the system-level result must be tested in the real electrical environment.

8. BESS current sensing review checklist

☐ Measurement point identified☐ DC, AC or AC+DC requirement defined☐ Bidirectional range and polarity confirmed☐ Continuous and transient currents reviewed☐ Accuracy and temperature conditions checked☐ Bandwidth and response time established☐ Isolation and safety requirements verified☐ Output and power interfaces compatible☐ Busbar and mounting geometry reviewed☐ Manufacturer datasheet and revisions checked

Conclusion

Current measurement in a battery energy storage system is not one single sensor-selection problem. The battery-side DC connection, converter stages and control or protection functions can impose different requirements. A sound review starts with the measurement location and current waveform, then evaluates accuracy, transient behavior, isolation, installation and interfaces against verified manufacturer documentation.

Manufacturer and engineering references
  1. LEM — Application Guide (application-based sensor placement and product guidance, including battery energy storage systems)
  2. Texas Instruments — Understanding Current Sensing in HEV/EV Batteries (technology principles and tradeoffs; automotive-battery context, not BESS-specific certification)
  3. Texas Instruments — TIDA-01141 High-Side Bidirectional Shunt Current Measurement Reference Design (an illustrative low-voltage implementation, not a universal BESS design)

Use the latest manufacturer datasheet and application notes for a particular part number. Technical suitability and system safety require independent engineering assessment.